Перейти к содержимому
10PCS IR Infrared Sensor Module Slotted Optical Optocoupler Speed Measuring Sensor Module Photo Interrupter Sensor Motor Speed Detection Robot для Arduino

Price:

$ 17,04


10PCS IR Infrared Sensor Module Slotted Optical Optocoupler Speed Measuring Sensor Module Photo Interrupter Sensor Motor Speed Detection Robot для Arduino

https://m.media-amazon.com/images/I/61idQiaR11L.jpg
8 sold in last 24 hours
  • Применяя фотоэлектрический датчик типа слота, он состоит из инфракрасного светодиода и фотоэлектрического транзистора NPN с шириной слота 5,9 мм.
  • Пока непрозрачный объект проходит через слот, он может вызвать выход низкого уровня TTL.
  • Использование триггера Шмидта для дрожи очень стабильно и может использоваться для измерения скорости автомобиля, измерения расстояния и других применений!
  • Установите отверстия с винтами M3 на обоих концах.
  • Рабочее напряжение: 3.3В-5В, выходная форма: выход цифрового переключателя (0 и 1)

$ 17,04 17.04 USD $ 17,04

Not Available For Sale

($ 1,70 / Units)
7 people are viewing this right now

  • Производитель
  • Подсчет
  • бренд
  • Количество пунктов
  • Элемент Питч
  • Напряжение
  • Материал
  • цвет
  • Тип подключения
  • Тип установки
  • Количество контактов
  • Тип материала
  • Количество позиций
  • Количество поляков
  • Тип продукта
  • стучать

Такой комбинации не существует.

Фотоэлектрические датчики

Условия и положения
30-дневная гарантия возврата денег
Доставка: 2-3 рабочих дня

Estimated shipping
Select a product to estimate shipping.

Instructions for use:
After connecting VCC and GND, the module signal indicator light will light up. When there is no obstruction in the module slot, the receiver tube will conduct and the module OUT will output a high level; When obstructed, OUT outputs a low level and the signal indicator light goes out. The module OUT can be connected to a relay to form a limit switch and other functions, and can also be connected to an active buzzer module to form an alarm. The OUT output interface can be directly connected to the IO port of the microcontroller, usually connected to an external interrupt to detect whether the sensor is blocked. If a motor encoder is used, the speed of the motor can be detected.
Precautions:
Correct wiring! Do not reverse the positive and negative connections to burn out the electronic components of the board. Players should set the I/O port of the MCU to input mode/receive mode, otherwise it cannot be used. Other MCUs, or more advanced control boards such as ARM, must be set to input/output mode if the I/O port needs to be set to input/receive mode, otherwise it cannot be used. The 51 series microcontroller can be used directly without the need to set input and output modes.

Main Specification
Производитель ЕС покупает
Подсчет 10 Граф
бренд ЕС покупает
Количество пунктов 1010
Элемент Питч 5.9 миллиметров
Напряжение 5 Вольт
Материал медь
цвет черный
Тип подключения винтовка
Тип установки К черту гору
Количество контактов 2 2
Technical Details
Тип материала медь
Количество позиций 1 1
Количество поляков 1 1
Others
Тип продукта Фотоэлектрические датчики
стучать 5.9 миллиметров